Once clients enable this extension, commands can no longer refer to "message
sequence numbers" (MSNs), but can only refer to messages with UIDs. This means
both sides no longer have to carefully keep their sequence numbers in sync
(error-prone), and don't have to keep track of a mapping of sequence numbers to
UIDs (saves resources).
With UIDONLY enabled, all FETCH responses are replaced with UIDFETCH response.
Initialize store and switchboard first, then open account, and close in reverse
order.
Replace all "CheckClosed" calls with "WaitClosed", future changings will keep
an account reference open for a bit after the last regular close, so we can't
know that an account should be closed during tests.
Remove one parameter from the (still too long) "start test server" function in
imapserver testing code.
logging of login attempts happens in the background, because we don't want to
block regular operation with disk since for such logging. however, when a line
is logged, we evaluate some attributes of a connection, notably the username.
but about when we do authentication, we change the username on a connection. so
we were reading and writing at the same time. this is now fixed by evaluating
the attributes before we pass off the logger to the goroutine.
found by the go race detector.
for admins to open an imap connection preauthenticated for an account (by address), also when
it is disabled for logins.
useful for migrations. the admin typically doesn't know the password of the
account, so couldn't get an imap session (for synchronizing) before.
tested with "mox localserve" and running:
mutt -e 'set tunnel="MOXCONF=/home/mjl/.config/mox-localserve/mox.conf ./mox admin imapserve mox@localhost"'
may also work with interimap, but untested.
i initially assumed imap would be done fully on file descriptor 0, but mutt
expects imap output on fd 1. that's the default now. flag -fd0 is for others
that expect it on fd0.
for issue #175, suggested by DanielG
to facilitate migrations from/to other mail setups.
a domain can be added in "disabled" mode (or can be disabled/enabled later on).
you can configure a disabled domain, but incoming/outgoing messages involving
the domain are rejected with temporary error codes (as this may occur during a
migration, remote servers will try again, hopefully to the correct machine or
after this machine has been configured correctly). also, no acme tls certs will
be requested for disabled domains (the autoconfig/mta-sts dns records may still
point to the current/previous machine). accounts with addresses at disabled
domains can still login, unless logins are disabled for their accounts.
an account now has an option to disable logins. you can specify an error
message to show. this will be shown in smtp, imap and the web interfaces. it
could contain a message about migrations, and possibly a URL to a page with
information about how to migrate. incoming/outgoing email involving accounts
with login disabled are still accepted/delivered as normal (unless the domain
involved in the messages is disabled too). account operations by the admin,
such as importing/exporting messages still works.
in the admin web interface, listings of domains/accounts show if they are disabled.
domains & accounts can be enabled/disabled through the config file, cli
commands and admin web interface.
for issue #175 by RobSlgm
Intended for future use with chatmail servers. Standard email ports may be
blocked on some networks, while the HTTPS port may be accessible.
This is a squashed commit of PR #255 by s0ph0s-dog.
the imap & smtp servers now allow logging in with tls client authentication and
the "external" sasl authentication mechanism. email clients like thunderbird,
fairemail, k9, macos mail implement it. this seems to be the most secure among
the authentication mechanism commonly implemented by clients. a useful property
is that an account can have a separate tls public key for each device/email
client. with tls client cert auth, authentication is also bound to the tls
connection. a mitm cannot pass the credentials on to another tls connection,
similar to scram-*-plus. though part of scram-*-plus is that clients verify
that the server knows the client credentials.
for tls client auth with imap, we send a "preauth" untagged message by default.
that puts the connection in authenticated state. given the imap connection
state machine, further authentication commands are not allowed. some clients
don't recognize the preauth message, and try to authenticate anyway, which
fails. a tls public key has a config option to disable preauth, keeping new
connections in unauthenticated state, to work with such email clients.
for smtp (submission), we don't require an explicit auth command.
both for imap and smtp, we allow a client to authenticate with another
mechanism than "external". in that case, credentials are verified, and have to
be for the same account as the tls client auth, but the adress can be another
one than the login address configured with the tls public key.
only the public key is used to identify the account that is authenticating. we
ignore the rest of the certificate. expiration dates, names, constraints, etc
are not verified. no certificate authorities are involved.
users can upload their own (minimal) certificate. the account web interface
shows openssl commands you can run to generate a private key, minimal cert, and
a p12 file (the format that email clients seem to like...) containing both
private key and certificate.
the imapclient & smtpclient packages can now also use tls client auth. and so
does "mox sendmail", either with a pem file with private key and certificate,
or with just an ed25519 private key.
there are new subcommands "mox config tlspubkey ..." for
adding/removing/listing tls public keys from the cli, by the admin.
for some errors during the scram authentication protocol, we would treat some
errors that a client connection could induce as server errors, printing a stack
trace and aborting the connection.
this change recognizes those errors and sends regular "authentication failed"
or "protocol error" error messages to the client.
for issue #222 by wneessen, thanks for reporting
an é (e with accent) can also be written as e+\u0301. the first form is NFC,
the second NFD. when logging in, we transform usernames (email addresses) to
NFC. so both forms will be accepted. if a client is using NFD, they can log
in too.
for passwords, we apply the PRECIS "opaquestring", which (despite the name)
transforms the value too: unicode spaces are replaced with ascii spaces. the
string is also normalized to NFC. PRECIS may reject confusing passwords when
you set a password.
to get the security benefits (detecting mitm attempts), explicitly configure
clients to use a scram plus variant, e.g. scram-sha-256-plus. unfortunately,
not many clients support it yet.
imapserver scram plus support seems to work with the latest imtest (imap test
client) from cyrus-sasl. no success yet with mutt (with gsasl) though.
and change thunderbird autoconfiguration to use it.
unfortunately, for microsoft autodiscover, there appears to be no way to
request secure password negotiation. so it will default to plain text auth.
cram-md5 is less secure than scram-sha-*, but thunderbird does not yet support
scram auth. it currently chooses "plain", sending the literal password over the
connection (which is TLS-protected, but we don't want to receive clear text
passwords). in short, cram-md5 is better than nothing...
for cram-md5 to work, a new set of derived credentials need to be stored in the
database. so you need to save your password again to make it work. this was
also the case with the scram-sha-1 addition, but i forgot to mention it then.
the idea is that clients may not support SCRAM-SHA-256, but may support
SCRAM-SHA-1. if they do support the 256 variant, they'll use it.
unfortunately, thunderbird does not support scram-sha-1 either.
