NOTIFY is like IDLE, but where IDLE watches just the selected mailbox, NOTIFY
can watch all mailboxes. With NOTIFY, a client can also ask a server to
immediately return configurable fetch attributes for new messages, e.g. a
message preview, certain header fields, or simply the entire message.
Mild testing with evolution and fairemail.
It still blocks on reading partial flushes from clients, preventing progress
and eventually timing out. The flate library needs more changes to make this
work.
Connections from iOS mail sometimes timed out, not always.
The extension is simply not announced, code is still present.
Writing to a connection goes through the flate library to compress. That writes
the compressed bytes to the underlying connection. But that underlying
connection is wrapped to raise a panic with an i/o error instead of returning a
normal error. Jumping out of flate leaves the internal state of the compressor
in undefined state. So far so good. But as part of cleaning up the connection,
we could try to flush output again. Specifically: If we were writing user data,
we had switched from tracing of protocol data to tracing of user data, and we
registered a defer that restored the tracing kind and flushed (to ensure data
was traced at the right level). That flush would cause a write into the
compressor again, which could panic with an out of bounds slice access due to
its inconsistent internal state.
This fix prevents that compressor panic in two ways:
1. We wrap the flate.Writer with a moxio.FlateWriter that keeps track of
whether a panic came out of an operation on it. If so, any further operation
raises the same panic. This prevents access to the inconsistent internal flate
state entirely.
2. Once we raise an i/o error, we mark the connection as broken and that makes
flushes a no-op.
REPLACE can be used to update draft messages as you are editing. Instead of
requiring an APPEND and STORE of \Deleted and EXPUNGE. REPLACE works
atomically.
It has a syntax similar to APPEND, just allows you to specify the message to
replace that's in the currently selected mailbox. The regular REPLACE-command
works on a message sequence number, the UID REPLACE commands on a uid. The
destination mailbox, of the updated message, can be different. For example to
move a draft message from the Drafts folder to the Sent folder.
We have to do quite some bookkeeping, e.g. for updating (message) counts for
the mailbox, checking quota, un/retraining the junk filter. During a
synchronizing literal, we check the parameters early and reject if the replace
would fail (eg over quota, bad destination mailbox).
to compress the entire IMAP connection. tested with thunderbird, meli, k9, ios
mail. the initial implementation had interoperability issues with some of these
clients: if they write the deflate stream and flush in "partial mode", the go
stdlib flate reader does not return any data (until there is an explicit
zero-length "sync flush" block, or until the history/sliding window is full),
blocking progress, resulting in clients closing the seemingly stuck connection
after considering the connection timed out. this includes a coy of the flate
package with a new reader that returns partially flushed blocks earlier.
this also adds imap trace logging to imapclient.Conn, which was useful for
debugging.
they are intended to be used by the server to automatically mark some messages
as important, based on server-defined heuristics. we don't have such heuristics
at the moment. perhaps in the future, but until then there are no plans.
we already supported special-use flags. settable through the webmail interface,
and new accounts already got standard mailboxes with special-use flags
predefined. but now the IMAP "CREATE" command implements creating mailboxes
with special-use flags.
to get the security benefits (detecting mitm attempts), explicitly configure
clients to use a scram plus variant, e.g. scram-sha-256-plus. unfortunately,
not many clients support it yet.
imapserver scram plus support seems to work with the latest imtest (imap test
client) from cyrus-sasl. no success yet with mutt (with gsasl) though.
the idea is that clients may not support SCRAM-SHA-256, but may support
SCRAM-SHA-1. if they do support the 256 variant, they'll use it.
unfortunately, thunderbird does not support scram-sha-1 either.
